OBD-II trouble code · Powertrain (engine and transmission)

P0151 O2 Sensor Circuit Low Voltage Bank 2 Sensor 1

The front oxygen sensor on engine Bank 2 is reporting a voltage that stays too low, which normally means it is seeing a lean (extra-air) exhaust or the signal is being pulled down by a fault. Because this sensor helps set the fuel mixture, the problem can affect fuel economy and emissions.

SeverityModerate
Safe to drive?Usually safe to drive short-term if the engine runs normally, but get it checked soon because a lean condition can raise engine temperatures and hurt the catalytic converter; if the check-engine light flashes, stop driving.

My front oxygen sensor on Bank 2 keeps telling me the exhaust is lean. Let's figure out if I'm really sucking in extra air or if the sensor itself is just tired.

— FRED, speaking as your car

What P0151 means

Oxygen sensors produce a voltage that swings between roughly 0.1 and 0.9 volts as the exhaust goes lean and rich. The engine computer (PCM) set this code because the Bank 2 Sensor 1 signal stayed below its expected range for longer than allowed while the engine was warm and in closed-loop operation. Bank 2 is the side of a V6, V8 or other V/flat engine opposite cylinder number 1; inline engines do not have a Bank 2. Sensor 1 is the upstream oxygen sensor, mounted before the catalytic converter, and it is the one the computer uses to fine-tune the fuel mixture. A low reading can be a genuine lean condition (such as a vacuum leak on that bank), an exhaust leak ahead of the sensor letting in outside air, or an electrical problem such as a shorted signal wire or a failed sensor. Exact test conditions and thresholds vary by make and model.

Common symptoms

  • Check engine light on
  • Reduced fuel economy
  • Rough or hesitant idle on some vehicles
  • Possible lean-related codes on the same bank
  • May fail an emissions inspection

Likely causes (most likely first)

  1. Vacuum or intake air leak affecting Bank 2
  2. Exhaust leak upstream of the sensor (manifold gasket, cracked manifold)
  3. Failed or contaminated oxygen sensor
  4. Signal wire shorted to ground or damaged connector
  5. Low fuel pressure or restricted injectors on that bank
  6. Unmetered air from a faulty MAF sensor reading

What you can check yourself

  1. Read freeze-frame data and check for other codes, especially P0174 (Bank 2 lean) or misfire codes
  2. With an OBD-II app, watch the sensor voltage at warm idle; a healthy front sensor switches rapidly between low and high, while a stuck-low one sits near 0.1 V
  3. Check long-term fuel trims for that bank; high positive trims point to a real lean condition rather than a bad sensor
  4. Listen and look for vacuum leaks (cracked hoses, intake boot) and exhaust leaks near the manifold
  5. Locate the correct sensor: on the side opposite cylinder 1, before the catalytic converter (often in or near the exhaust manifold). A repair manual or online diagram for your exact engine helps, because swapping the wrong sensor is a common and wasted expense.
  6. Inspect the sensor wiring and connector for melted insulation, chafing on the exhaust, or corrosion

FRED reads freeze frame and live data, so you can see what the engine was doing when P0151 set, before you buy any parts.

Typical repair costs

RepairTypical range
Diagnose and repair vacuum/intake leak$100–$400
Replace upstream oxygen sensor$175–$500
Repair exhaust manifold gasket or leak$200–$900
Repair sensor wiring or connector$100–$300

Typical US independent-shop ranges, parts and labor. Your price varies by vehicle, region and shop.

Get a second opinion from your own car. Plug a $15–30 OBD-II adapter into the port under your dash, open FRED and ask “Fred, what are my codes?” Get the free beta →
Which adapter?

P0151 FAQ

No. A low reading from a front sensor often means the sensor is accurately reporting a lean condition caused by a vacuum or exhaust leak. Checking fuel trims and looking for leaks before buying a sensor can save money.
Running lean for a long time can make the engine and converter run hotter and can upset the converter's chemistry, so it is worth fixing promptly rather than ignoring.

Related codes