OBD-II trouble code · Powertrain (engine and transmission)

P0013 Exhaust Camshaft Position Actuator Circuit/Open Bank 1

The engine computer found an electrical problem in the circuit that controls the exhaust camshaft timing adjuster on bank 1. The adjuster may not be moving the cam timing the way it should, which can affect power, idle, and fuel economy.

SeverityModerate
Safe to drive?Usually OK to drive short-term to get it checked, because the engine typically defaults to a fixed cam position, but stop driving if the check-engine light flashes or the engine runs very rough.

Hey, the little valve that adjusts my exhaust cam timing on bank 1 isn't answering my calls. I'll keep running, but let's check that plug and wiring before it turns into a bigger timing headache.

— FRED, speaking as your car

What P0013 means

Engines with variable valve timing use an oil control solenoid (also called an actuator or OCV) to shift the exhaust camshaft's timing. The engine computer (PCM) sends a controlled signal to that solenoid and monitors the circuit. P0013 sets when the PCM sees a circuit fault such as an open wire, a short, or a resistance reading outside the expected range on the bank 1 exhaust (the 'B' camshaft) actuator circuit. It is an electrical code, not a mechanical timing code, though a failed solenoid can cause both. Which side is bank 1 and exactly which cam is 'B' varies by make, so check a service reference for your engine.

Common symptoms

  • Check-engine light on
  • Rough or unstable idle
  • Reduced power or sluggish acceleration
  • Worse fuel economy
  • Occasional stalling or hesitation
  • Sometimes no noticeable symptom at all

Likely causes (most likely first)

  1. Failed exhaust camshaft oil control solenoid (actuator)
  2. Damaged, corroded, or loose connector at the solenoid
  3. Open or shorted wiring between the solenoid and the PCM
  4. Low or dirty engine oil affecting solenoid operation
  5. Blown fuse or power-feed issue to the solenoid circuit
  6. Rarely, a PCM driver fault

What you can check yourself

  1. Read all stored codes and freeze-frame data with your OBD-II adapter and note any other cam or timing codes
  2. Check engine oil level and condition; top up or change if low or sludgy
  3. Locate the bank 1 exhaust cam solenoid and inspect its connector for corrosion, bent pins, or oil intrusion
  4. Inspect the harness for chafing or heat damage near the valve cover and exhaust
  5. Measure the solenoid's resistance with a multimeter and compare to the spec for your engine
  6. Clear the code and see whether it returns immediately (hard fault) or only after driving (intermittent)

FRED reads freeze frame and live data, so you can see what the engine was doing when P0013 set, before you buy any parts.

Typical repair costs

RepairTypical range
Oil and filter change with correct-spec oil$50–$120
Repair connector or wiring to the cam actuator solenoid$100–$300
Replace exhaust camshaft oil control solenoid$150–$450
Diagnose and replace cam phaser if solenoid is good but timing is faulty$600–$1,800

Typical US independent-shop ranges, parts and labor. Your price varies by vehicle, region and shop.

Get a second opinion from your own car. Plug a $15–30 OBD-II adapter into the port under your dash, open FRED and ask “Fred, what are my codes?” Get the free beta →
Which adapter?

P0013 FAQ

Low or sludgy oil can make the solenoid misbehave, but P0013 is mainly an electrical circuit code. Fresh oil is a cheap first step, but the wiring and solenoid usually need checking too.
No. P0013 points to the actuator's electrical circuit, while P0014 means the exhaust cam timing is more advanced than the computer commanded, which is a performance issue.

Related codes